The E10 error on your Hoover Washing means the machine is not filling with water properly or quickly enough. This is typically caused by water supply issues or blocked inlet components that prevent water from reaching the drum within the expected time.
| Error code | E10 |
|---|---|
| Meaning | Water fill fault - machine cannot fill with water within the allocated time |
| Severity | Medium — machine will not operate until resolved |
| Time to fix | 10–30 minutes |
| Tools needed | Pliers, towel, small brush or None |
What the E10 error means
The E10 error code indicates a water inlet failure on your Hoover washing machine. When you start a wash cycle, the machine expects to fill with water within a specific timeframe, usually around 8 to 10 minutes. If the water level does not reach the required amount within this period, the control board triggers the E10 error and stops the cycle to prevent damage or improper washing.
This error is one of the most common issues with Hoover washing machines and is almost always related to the water supply system rather than internal mechanical failures. The good news is that most causes can be diagnosed and fixed without calling a professional engineer.
Common causes
- Water supply taps turned off or not fully opened behind the machine
- Blocked or clogged inlet filter screens where hoses connect to the machine
- Kinked, twisted or damaged water inlet hose restricting water flow
- Low water pressure in your home supply system
- Faulty inlet valve that cannot open properly to allow water through
- Frozen pipes in cold weather preventing water from reaching the machine
How to fix the E10 error
- Check the water supply taps Locate the water supply taps behind your washing machine, usually connected to the wall. Ensure both hot and cold taps (or just cold on some models) are fully turned on. Sometimes taps can be accidentally knocked or partially closed during cleaning. Turn them fully anticlockwise to open completely, then try running a cycle again.
- Inspect and clean the inlet filter screens Turn off the water supply taps and unplug the machine. Unscrew the inlet hoses from the back of the washing machine using pliers if needed. You will see small mesh filters inside the inlet valve ports. Carefully remove these filters with pliers or tweezers and rinse them under running water to remove any debris, limescale or sediment. Replace the filters, reconnect the hoses tightly, turn the water back on and test the machine.
- Examine the inlet hose for damage Check the entire length of the water inlet hose from the tap to the machine. Look for kinks, twists, or flat sections that could restrict water flow. Straighten any kinks and ensure the hose is not trapped behind the machine. If the hose appears damaged, cracked or has weak spots, replace it with a new inlet hose available from hardware stores or appliance parts suppliers.
- Test your home water pressure Turn on a nearby tap fully and observe the water flow. If pressure seems low throughout your home, contact your water supplier as this may be a broader issue. If only the washing machine is affected, the problem is likely with the inlet components. You can also disconnect the inlet hose from the machine and hold it over a bucket while turning on the tap to verify good water flow.
- Reset the washing machine After checking all water supply issues, unplug the machine from the electrical socket for 2 to 3 minutes. This resets the control board and clears temporary errors. Plug the machine back in and run a short rinse cycle to see if the E10 error has cleared.
- Check the inlet valve for faults If all external checks pass but the error persists, the inlet valve inside the machine may be faulty. The valve has electrical solenoids that open to allow water in. Access the valve by removing the top panel of the machine. Use a multimeter to test for continuity across the valve terminals (usually around 3000 to 4000 ohms). If the valve fails this test or shows visible damage, it needs replacement.
FAQ
Can I still use my Hoover washing machine with an E10 error?
No, you cannot use the machine while the E10 error is active. The washing machine will not fill with water and cannot complete any wash cycle. You must resolve the water supply issue before the machine will operate normally.
How much does it cost to fix an E10 error on a Hoover washing machine?
If the issue is a blocked filter or closed tap, the fix costs nothing. A replacement inlet hose costs between 10 and 20 pounds. If you need to replace the inlet valve, the part costs 20 to 40 pounds. Professional repair callouts typically range from 60 to 120 pounds including labour, though most E10 errors can be fixed yourself.
Why does my Hoover washing machine show E10 only sometimes?
Intermittent E10 errors usually indicate partially blocked inlet filters or inconsistent water pressure in your home supply. The blockage may allow enough water through when pressure is higher but fail when pressure drops. Clean the inlet filters thoroughly and check for debris that might move around and cause intermittent blockages.
